PO
Box 6218
Colorado Springs, CO 80934
P: 719-684-8168
F: 719-684-9615
WRS Information Menu
WRS 12 and 12+
WRS 42
WRS 52
Back to Main Menu
© 2009
Cascade Engineering Inc.
|
WRS 32 WATER RECYCLE SYSTEM
SPECIFICATIONS

The WRS 32 Recycle System is designed to solve your washwater
disposal problems. This COMPLETELY AUTOMATIC TREATMENT SYSTEM
will collect your dirty, oily washwater and process it so that it can be
reused in your washing operation. The feed pump transfers the dirty
water from a collection sump to the treatment unit. Reagents are added
to the water to kill bacteria and odors, neutralize the pH, and remove
pollutants such as oil, grease, dirt, and sludge. These reagents, which
are commonly used in drinking water treatment, actually make the water
much more ENVIRONMENTALLY FRIENDLY and less hazardous for
personnel doing the washing. The treated water is then stored until
needed for washing. The WRS 32 treats up to 8 gpm (12000 gpd),
which is more than enough for most washing operations. This unit is
equipped with many convenience features, including automatic priming
valves for the reagent pumps, integral water storage tank, and filters
status pressure gage. It comes completely assembled and wired, ready
to be set in place and plugged into a 15 amp, 115 volt outlet. The
water discharge from the integral storage tank is pressurized to
feed your pressure washers, even if they are remotely located. Premium
components and quality construction insure the most troublefree
operation possible.
WRS 32 WATER RECYCLE SYSTEM SPECIFICATIONS
| Rated flow rate: |
Up to 8 gpm (12000 gpd) |
| Electrical requirement: |
115 VAC, 60 Hz, 1 phase, 15 amp total |
| Recycle feed pump: |
Self priming centrifugal cast iron pump with 1/2
HP thermally protected motor. Mounted on the machine base.
Controlled by float switch in collection pit. Suction line
strainer and foot valve are provided. |
| Discharge pump: |
High head centrifugal pump with 1/2 HP thermally
protected motor. Provides pressurized water flow to pressure
washer and other uses. |
| Electrical controls: |
GFCI provided, prewired with 15 amp plug, 10 ft
cord Lighted switches for power, feed pump, coagulant pump,
oxidizer pump, pH adjuster pump, makeup water, and manual drain.
pH controller with digital display. NEMA 4 rated enclosure |
| Reagent metering pumps: |
Electronic controlled diaphragm pumps with stroke
rate and stroke length controls and auytomatic degassing head
for ease of priming. Three pumps are supplied, for coagulant,
oxidizer, and pH adjuster. Pumps are mounted in a fiberglass
enclosure. |
| Inlet strainer: |
Large size with stainless steel screen in
corrosion resistant plastic housing. |
| Filter system: |
Two 20" long 20 micron filter cartridges for
final polishing. Two sets included. |
| Sludge collection system: |
Three large, disposable fabric socks collect
sludge. Two sets included with machine. |
| Make up water: |
100 psi maximum pressure. Automatically added as
required by application. |
| Recycle tank capacities: |
Coagulant tank- 120 gallons
Separator tank- 120 gallons
Storage tank- 120 gallons
Total water capacity- 360 gallons
|
| Recycle construction: |
Heavy duty polypropylene tank with unitized
construction. Schedule 80 PVC pipe used throughout. Heavy steel
base assembly. |
| Connection sizes: |
Machine inlet- 1 1/2 MNPT
Treated water outlet- 3/4 FNPT
Drain line- 1 FNPT
Make up water- 1/2 FNPT
|
| Overall dimensions: |
7 ft 6 in long, 3 ft 2 in deep, 4 ft 3 in tall |
| Shipping weight: |
800 pounds |
| Options: |
Second pH adjusting pump. Additional treated
water storage capacity. Sand filter final polishing system.
Activated carbon water polishing systems. Ozone treatment.
Pretreatment systems, oil skimmers, and oily water separators. |
|